When a property manager gets a maintenance call about an outlet that stopped working or a breaker that will not hold, the job needs to go to someone who can scope it correctly the first time. Rental properties, commercial spaces, and older residential homes in a town this size generate a steady mix of repair calls, panel questions, and wiring work that has been sitting on a to-do list too long. We handle all of it, and the first conversation happens on the phone before anything is scheduled.
Working here means getting the diagnosis right before the work starts. That applies whether the call comes from a landlord with a tenant complaint, a contractor finishing a remodel, or a homeowner who noticed something wrong and wants a straight answer about what it takes to fix it.
Call (530) 461-5942 and describe what you are seeing.
Every house has a history, and some of that history shows up in the walls. Aluminum branch-circuit wiring from the 1960s and 1970s, outlets added without a permit, panels that were modified by someone who knew just enough to make it look finished, and GFCI protection that was never installed where the code now requires it are all things we run into during repair calls and inspections.
The question is always whether a repair holds or whether the underlying condition needs to be addressed first. A failed outlet on a circuit with otherwise sound wiring is a repair. An outlet on an aluminum-wired circuit that has never had the correct remediation is a different situation, and a repair that ignores that will not hold.
We explain the difference before any work starts. If the existing wiring can support a correct repair, we say so. If the condition behind the fault is what needs attention, we scope that clearly so you can decide how to proceed.
Missing ground-fault and arc-fault protection is one of the most common findings on older properties. GFCI outlets belong in kitchens, bathrooms, garages, and anywhere near water. AFCI protection is required on bedroom circuits in current code, and many homes that predate that requirement have never been updated. Installing the correct protection is straightforward work, and it brings those circuits up to the standard the next inspection expects.
An outlet that has never worked since the last tenant moved out, a switch that sparks when you flip it, an exterior light that has been disconnected for two years because nobody got around to replacing the fixture. These are the jobs that stay on the list because they seem minor. Most of them are minor. Some of them are not.
A sparking switch is usually a failing device, but it can also be a loose connection that has been arcing for long enough to char the wiring behind it. An outlet that has never worked might trace back to a tripped GFCI somewhere upstream, or it might be a wiring fault that was there when the house was built. The only way to know is to look.
Small jobs are worth scheduling because the diagnostic visit is the same whether the problem turns out to be simple or complicated. Prompt response, even for last-minute electrical calls, means a problem that could get worse does not have to wait for a convenient window.
Tenants who cannot be without power during business hours, a household that needs the kitchen circuit back before dinner, a commercial space that cannot go dark in the middle of the day. These are real constraints and they come up regularly.
The call is where we work that out. When you describe the situation, we confirm what the schedule allows and how the visit will be sequenced so disruption is limited. If the problem will not keep, we take short-notice work and answer those calls. The rate is set on the phone before anyone is sent out, so there are no open questions about cost going into it.
Electrical work done to the standard the next inspection expects does not require tearing a property apart to get there. We confirm what the visit will involve before we arrive.
A panel that was sized for a house with a gas range, no air conditioning, and no power-hungry appliances is a different thing from a panel that needs to carry an EV charger, a battery backup system, and a new subpanel for a garage workshop. The gap between what a property has and what it needs to carry shows up as tripping breakers, slow charging, or a quote from a contractor that says the panel has to go first.
Before any new circuit is added, we run a load calculation to confirm the existing service can carry it. A 200-amp panel that is already running near its limit cannot simply absorb another 50-amp circuit without something giving way. The calculation tells us whether the panel can support the addition, whether a service upgrade is the right first step, or whether the load can be managed by reorganizing what is already there.
A service upgrade replaces the existing panel with one sized for the home's actual load. The work involves the main panel, the service entrance, and the branch circuits that feed from it. Where a subpanel is the right answer for a detached garage or an addition, we handle that as well. The scope is confirmed on the call so you know what the project involves before it starts.
Straight scheduling. Upfront pricing. Code-compliant wiring.
The price for electrical work depends on what the job actually involves. A circuit repair on accessible wiring in a straightforward panel is a different scope from the same repair behind finished walls with a panel that needs attention before the new circuit can be added. What the fault turns out to be, what has to be opened up to reach it, and whether the existing circuit or panel can carry the change are the things that move the number.
We confirm the rate on the phone based on what you describe. If the job turns out to be more involved once we are on site, we explain what changed before the work changes. You get the price before anything is scheduled, and the scope is clear before anyone arrives.
Call (530) 461-5942 and ask what it covers.
The person who answers knows the trade and can scope the job from what you describe. One call is enough to get the visit booked.
The jobs in this section come up when something in a property changes: a new appliance, a different use for the garage, a vehicle that needs charging overnight, or a panel that has never been properly labeled.
A dryer, electric range, hot tub, or large workshop appliance draws enough current to require its own dedicated circuit. Running a high-draw appliance on a shared circuit is what causes the repeated trips and the performance problems that follow. We run the dedicated circuit, install the correct outlet or disconnect, and confirm the panel has capacity before the circuit is energized.
A Level 2 EV charger needs a dedicated 240-volt circuit run from the panel to the garage or parking area. EV ownership in the Sacramento region has grown to the point where this is a routine request, and the process is the same on every job: panel capacity check first, then the circuit, then the charger connection. If the panel needs an upgrade to support the charger, we scope that as part of the same conversation.
New outlet installation, GFCI replacements, dimmer switches, smart switch wiring, and weatherproof outdoor receptacles all fall here. These are often the jobs that come out of an inspection finding or a remodel that left a few items unfinished. We handle them as standalone calls or as part of a larger visit.
A garage or workshop that runs a welder, air compressor, or heavy shop equipment needs circuits sized for that load. Standard household circuits are not built for it, and the breaker trips confirm that quickly. We run the correct gauge wire, install the right breaker, and make sure the panel can carry the addition.
A panel with missing labels or circuits that no longer match what they feed is a real problem when a fault needs to be traced or a breaker needs to be turned off in a hurry. We trace each circuit, confirm what it feeds, and label the panel correctly. It is a job that takes time to do right and pays for itself the first time something needs to be isolated quickly.
We serve Lemon Hill and the communities nearby throughout Sacramento County, including Fruitridge Pocket, Parkway, Florin, and Sacramento. West Sacramento is covered as well. If you are in the area and not sure whether we reach you, call and we will confirm. For the full list, go to our services page for electrical work.
Yes. If you want a diagnosis and a recommendation without committing to the repair on the same day, we can scope the problem and explain the options. The decision on how to proceed stays with you.
We scope the job on the phone based on what the tenant or manager describes, confirm the rate before anyone is sent out, and explain what the visit will involve so there are no open questions going in. If the fault turns out to be more involved than the initial description suggested, we explain what changed before the scope changes. The goal is a repair that holds, not a surface fix that comes back as another call.
Yes. Generator hookup involves installing a transfer switch at the panel, running the connection to the generator inlet, and confirming the circuits are balanced for the generator's rated output. Wildfire-season grid events are a real concern across this region, and a properly connected generator is the practical answer for a property that cannot afford to go dark. We handle the wiring and the panel connection.
Call (530) 461-5942 and describe the generator and the property and we will scope the job from there.
Homes built in the 1960s and 1970s in Sacramento County and the surrounding area sometimes have aluminum branch-circuit wiring, which requires specific remediation rather than a standard repair. Knob-and-tube wiring, ungrounded two-prong outlets throughout, and fuse boxes that have never been replaced are also findings we see on older properties. An inspection identifies what is present and what it would take to bring the system up to current standards.
Call (530) 461-5942 and describe the property and we can scope an inspection from there.
Electrical work does not have to sit on the list. Whether the job is a repair that came up this morning or a panel upgrade that has been on the radar for a year, the next step is the same.
Call El Dorado Hills Electrical Company at (530) 461-5942, describe what you are dealing with, and get the rate and the schedule on that call.
We are open seven days a week, 7:30 AM to 8:30 PM. The phone is the only step between you and a booked visit.
Electrical service reaches these neighboring areas too: Florin, Rosemont, La Riviera, Arden-Arcade, Vineyard.
Check our full list of towns.
We handle electrical work across the board, from a single dead outlet to a full panel replacement or new circuit for an EV charger. The table below breaks down what each service covers, who it fits best, and a practical note to help you decide what to ask about when you call. Pricing is confirmed on the call before anything is scheduled.
| Service | What It Covers | When You Need It | Good to Know |
|---|---|---|---|
| Electrical Panel & Service UpgradesMost Popular |
| Homes with an undersized panel, a fuse box, or plans to add EV charging or battery storage | A load calculation before the upgrade confirms the new panel is sized for what the home actually draws, not just the minimum code allows. |
| EV Charger Installation |
| EV owners who want reliable home charging rather than a standard wall outlet | We check panel capacity before running the circuit. If the panel needs an upgrade to support the charger, we scope that as part of the same conversation. |
| Standby Battery for Outages |
| Homeowners who want selected circuits to stay live during a grid outage | The transfer switch is what prevents backfeed to the grid and allows the generator or battery to carry selected circuits safely. We handle the wiring and panel connection. |
Call (530) 461-5942 to describe the job and get a straight answer about what it involves and what it will cost.
(530) 461-5942